Ask An Expert
Our Ask An Expert knowledge base contains answers to questions from designers like you. Browse the knowledge base by category or search key words. Not seeing what you need? Ask An Expert a question of your own.
Hi, i need a non-isolated 5V~6V output, and Iout max to 350ma AC-DC power supply solution. Would you please send me a schematic?
19
2015-07-03 04:31:25.323
Hi This is govindarajan,from sanmina india private limited,chennai.i need clarifiation between ESD11B5.0ST5G Vs SSESD11B5.0ST5G
98
2015-05-21 11:13:49.223
AMIS42770 - Can we use this IC as Repeater as well as Node at the same time?
227
2015-03-27 11:06:38.95
Alternator voltage controller semiconductor 029 ON J44E3G
332
2015-02-12 03:14:09.657
Can you clarify the functionality of the Vref pin on the AMIS 42770 Dual high speed CAN transceiver.
Thank you.
Niall Marriott
499
2015-01-28 10:06:39.195
Hello there!
I have a question on NCP59748, the very low-dropout regulator, which has two output pins but just one feedback ( FB ) pin.
I wonder if there were two divided op-amps in the IC package, the Vout of op-amp connected with two output pins separately and the feedback circuit are attached together in the IC. I searched the datasheet but it seems that the simplified application circuit showed only one output pin in the datasheet file. I have no clue that if the other output pin is just like what I think. Please let me know the detail of NCP59748 and I appreciate your kindness.
Best Regards,
Jack Huang
428
2015-01-15 11:32:55.627
Hello, could you please tell me if there is a substitute / replacement for for part #cs51411edr8g and send me some specks please.as well as cost veriances. NOTE IM NOT SURE WHAT CATAGORY its for my clients /boards
576
2015-01-12 10:35:37.647
kindly suggest the cost effective solution for the following requirement,AC input - 230v DC output (isolated)- 15V Max output Current - 1A This section one we need for our AC motor controller.
554
2014-12-08 10:09:53.606
I'm looking for a transistor, I think. It has 049 305 5AVL with the ON in a circle so I assume it's your part. Can you tell me how to get more of them?
707
2014-09-16 13:09:14.224
Subject: Calculating Rt and Ct in fig. 12 of AND8253/D App Note by Lepkowski. Hi, I need to provide surge suppression for a CAN transceiver in a system that will be subjected to Power Short-Circuit tests. In these tests all external I/O are shorted to a 32V source for a one minute duration. An unprotected NUP2105L would breakdown, conduct and burnout during this test. Fig. 12 of AND8253/D App Note by Lepkowski shows a way to avoid this problem. My question is: how do I calculate the values of Rt and Ct? Should Rt be a "pulse withstanding" type? How much power can I let the NUP2105L dissipate safely? 250mW at 25deg C? What would be a good value for Ct? Is there anything special about Ct? Thank You.
1035
2014-06-05 09:17:18.661
I have a ON B11 30A component and i wanted to get the datasheet or information of this diode. Can someone be of help?
1073
2014-03-20 08:59:16.884
I was wondering if the AMIS-42700 can filter CAN messages between the two buses on the chip? Or possible between AMIS-42700 chips
1199
2014-03-18 10:09:26.608
Data Sheet for the voltage suppressor ESD Protection Diodes (SZESD9R3.3S) mentions that the SZ prefix is for Automotive and Other Applications Requiring "Unique Site and Control Change Requirements". Can someone explain what the "Unique Site and Control Change Requirements" are? I'm not sure what they are talking about. Thanks
1162
2014-03-12 13:05:01.023
seeking 3ph rectifier/nCh FET controller for alternator application
1147
2014-02-28 14:49:32.592
what is the difference between the AMIS42700 and AMIS42770?
1287
2014-02-18 13:11:55.421
In the datasheet for the NTK3134N MOSFET there are minimum and maximum values for the gate threshold voltage (Vth). min = 0.35V and max = 1V. How do I interpret this range? Is there hysteresis at play so that the transistor will turn on with a gate-to-source voltage above 1V and then turn off if the gate-to-source voltage goes below 0.35V? (It remains on below 1V but above 0.35V?)
1340
2014-01-28 12:35:52.542
We would like to know if the current PSpice model of 1SMB5931BT3 can possibly result to the Maximum surge power of 200 watts as shown in the Datasheet and if possible do you have a test circuit for this model
1127
2014-01-28 11:15:08.579
Hello, I am looking for a component which can provide enough protection for the Pulse 5b disturbanse which requested in ISO16750-2:2012, with the parameter td=400ms, Us=87V, Ri=0.5ohm. Do you have a recommendation on the part number of On-semi products? Thanks.
1285
2013-11-22 17:09:16.908
Does Onsemi provides driver files for ADM1034 device?
1451
2013-10-31 09:58:01.032
Can NCP1117 be safely used with -10°C room temperature? From the datasheet, NCP1117's operating ambient temperature is 0~125°C. However, the die junction temperature range is -55~150°C. It seems odd to me that the die may operate in -55°C, while it cannot operate in room temperature under zero celsius degree. Could you give me some hint?
I know NCV1117 is of improved spec; however, it is a bit more pricey.
Thanks.
1458
2013-09-06 16:14:46.551
Dear Sir/Madam,
i am a student and i am in the process of my thesis diploma. As part of it, i need a voltage regulator that will take as input 5V and will give as output 3V. Unfortunately i have searched everywhere and the only ones i find are those who give as output 3.3V.
After a good look at your site, i saw that you have some DC/DC converters like the NCP1402 that could do the job, but i am not so sure. The reason i need the specific regulator is because my power source is at 5Volts and for the needs of my circuit, i need at a specific IC a 3Volts Vref.
Do you think that you have something that could help me?
Thank you in advance,
Pantelis
1531
2013-08-19 15:26:26.843
Hello..My company is using your NCV7341 CAN transciever,just wondering what is the max power dissipation,also does the current consumption of the transciever varies with the data rate being used which is 225 kbps..looking for your fast response ,thank you in advance...
1660
2013-07-02 08:54:35.19
Do you have any information on charging of VRLA batteries used in motorcycles
1759
2013-04-04 10:01:43.963